3 min read
Are you Looking to have an Automated Purlin Stacker Installed at your Facility?
At The Bradbury Group, we are always looking for ways to enhance our roll forming lines. Our latest innovation is an...
Bradbury Stock & Pre-owned Equipment
View the equipment we have available for sale.
+1.620.345.6394
Biegemaster XBend Double Folder 21'
Status: Available Now
Condition: New
- 6400mm – 21’ maximum length with 5 Frames
- Fully automatic gripper system (21 feet - 6 units)
- Automatic sheet loading table (21 feet)
- Taper back-gauge with Grippers for 1250mm throat (21 feet - 16ga - 6 stops)
- Two Station Bending with Grippers (bend 2 parts simultaneously with one operator)
- Servo Hydraulic package (0-145-0 deg in approximately 2 seconds)
- Double finger for narrow part bending
- 24'' Touchscreen Controller
- Slitter with rotated cutting direction right to left
- Immediate Delivery
Biegemaster XBend Double Folder 10'
Status: Available Now
Condition: New
- 3100mm – 122” maximum length with 3 Frames
- Fully automatic gripper system with three (3) grippers and three (3) fingers – single motor back gauge, no tapering
- Material thickness adjustment
- High Speed Servo Hydraulic Package
- Slitter with left to right movement
- 18'' Touchscreen Controller
- Immediate delivery
Bradbury Cut-To-Length Line with 14' Stacker
Status: Available Now
Condition: New
Equipment List
- 12,000lb. Entry Coil Car
- 12,000lb. Uncoiler with Hydraulic Expansion and Hydraulic Payoff
- Roller Straightener – Two 5.00” Ø Pinch Rolls, Four 3.00” Ø Work Rolls
- Feeder (150 FPM), Film Applicator, and Mechanical Shear
- Drop Type Stacker – 14’ Capacity with fixed height receiving table with powered side traverse
Specifications
- Maximum Coil Weight – 12,000lbs.
- Coil Inside Diameter – 20” Nominal
- Maximum Coil Outside Diameter – 45”
- Coil Width – 24-49”
- Cut Length – 48-168”
- Mode of Operation - Centerline Justified, Feed-to-stop
- Incoming Power - 460V, 3 Phase, 60 Hertz
- Pneumatic Supply – 100 PSI clean and dry
- Material – Carbon Steel - Grade 33 (0.015-0.048”), Grade 50 (0.015-0.033”)
- Grade 80 (0.015-0.027”)
- - Aluminum – Painted – 24,000 PSI Yield (0.020-0.060”)
-1.png)
Powered Exit Conveyor with Side Discharge
Status: Available Now
Condition: New
- 40' Exit Conveyor
- 5 Side discharge paddles
- Slide table to the lower conveyor
- Immediate Delivery
Bradbury Recut AG Profile Tooling
Status: Available Now
Condition: Recut
- 3.5" Arbor
- 48" Rollspace
- L6 Thru Hardened Tool Steel
- Recut and Chromed
- 14 Passes
- No straightener Fixture
- No Spur Gears
- Immediate Delivery
Bradbury Industry R Panel Tooling
Status: Available Now
Condition: New
- Pre-Painted, Galvanized and Galvalume
- 60 KSI Yield Min. 70 KSI Yield Maximum– Grade D – 24 Ga.
- 85 KSI Yield Min. 105 KSI Yield Maximum – Grade E – 26 Ga.
- 0.026” Maximum, 0.018” Minimum
- D2 Tool Steel
- 14 Passes
- No Spur Gears
- Immediate Delivery
Panther Cub III™ Slit CTL
Status: Available Now
Condition: New
- Slit, Shear, and Recoil
- Moving front end allowing easy access
- Upcut shear
- Beck Automation Cobalt Control
TS12 Uncoiler
Status: Available Now
Condition: New
- Single mandrel, 12,000 lb. (5.4 Metric ton) capacity
- 48 1/2" (1230mm) Maximum material width
- Hydraulic drive payoff with loop control up to 200 FPM
- Hydraulic mandrel expansion
Self-contained hydraulic power unit - Expansion range 18" (457mm) - 21" (533mm)
TS12 Coil Car
Status: Available Now
Condition: New
- Cradle type
- 12,000 lbs. (5.4 Metric Ton) capacity
- Maximum coil dimensions: 48" (1220mm) X 45" (1143mm) OD
- Hydraulic power from recoiler unit
- Complete with track and hydraulic drive
- Coil Keepers are available
Coil Tipper
Status: Available Now
Condition: New
- 12,000 lb. Capacity
- Maximum Coil Dimensions 48" wide X 48" OD
- Self Contained Hydraulic Power Supply
- Approximate Cycle Time is 1 Minute
- 230 Volt, 60 HZ, 1 PH
